• SaveTheTuaHawk@lemmy.ca
        link
        fedilink
        English
        arrow-up
        11
        ·
        2 months ago

        No it isn’t. Read Zinn’s repair book or watch any video from Park Tool by Calvin and once you understand how simple it is, adjustment is trivial.

        • artyom@piefed.social
          link
          fedilink
          English
          arrow-up
          8
          arrow-down
          1
          ·
          2 months ago

          I’ve watched a dozen videos and completed as many alignments but it’s just never right.

        • sem@piefed.blahaj.zone
          link
          fedilink
          English
          arrow-up
          2
          ·
          2 months ago

          Rear derailer is usually trivial; only gets tricky if you’re adjusting the body screw and/or messing around with the chain. Front derailer sometimes necessitates adjusting the position on the bike frame. And especially with cheap 3x bikes can be tricky, or even impossible, to get it just right.

      • Fallibilist@feddit.uk
        link
        fedilink
        English
        arrow-up
        6
        arrow-down
        10
        ·
        2 months ago

        It’s not. Derailleur is set once when it’s installed onto the bike and you should never need to adjust it again. If the shifting is crap the issue is the twisted hanger and no amount of adjusting the limit screws is going to fix that.

        • unglueclass23@programming.dev
          link
          fedilink
          English
          arrow-up
          8
          ·
          2 months ago

          I had to re-index my gears ~2 years after I bought my new mountain bike… It’s not “hard” but if you’ve never done it before and don’t have a place where to properly work on your bike I can see why people would rather pay whatever the fee is at a shop.

          Like with most stuff you do it a couple of times and it becomes easy.

        • twix@infosec.pub
          link
          fedilink
          English
          arrow-up
          3
          ·
          2 months ago

          Well maybe (even though I do think a bit of a bent hanger can be compensated for) but even then it’s only true until you change cassette/chain or the shifter cable, which you will have to do at some point.

          • Fallibilist@feddit.uk
            link
            fedilink
            English
            arrow-up
            1
            ·
            2 months ago

            A new chain or cassette doesn’t affect the derailleur. A new cable does, but the tension is adjusted from the shifter, not by messing with the derailleur adjustments. It’s true that god-awful shifting due to a bent derailleur can be mitigated to some extent by messing with the adjustments but it’ll never be good. It can’t be because the derailleur is bent. Then when you replace the hanger with a straight one the shifting goes to shit again.

            Whenever my derailleur catches on a rock or a stump and the shifting goes to shit all I do is remove the derailleur from the hanger, use the hanger adjustment tool to straighten it out and once I re-attach the derailleur it shifts perfectly again with no adjusting at all.

            • twix@infosec.pub
              link
              fedilink
              English
              arrow-up
              2
              ·
              2 months ago

              It does tho. Not all cassettes are built on the same tolerances and different brands might have different interpretations of the standards, so always check the limits.
              Cable tension more often then not can be dialed on the derailleur as well.
              Worn chains can impact shift performance, and sometimes adjusting tension or derailleur height can improve things.
              These are things that aren’t noticed when everything is new and clean, but can slowly creep up as an issue.

              So yes. I agree with your sentiment that a well set up derailleur should keep shifting, in practice it’s more nuanced.

            • kestrel7_7@lemmy.world
              link
              fedilink
              English
              arrow-up
              1
              ·
              2 months ago

              Shit like this is why I will never own a derailleur bike again. Too much maintenance. I was constantly catching the derailleur on rocks and curbs and things like that, then having to do the finickiest mechanical work known to man. All just so I can go uphill slower?? Crazy technology!

        • artyom@piefed.social
          link
          fedilink
          English
          arrow-up
          1
          ·
          2 months ago

          So you’re saying it’s impossible to bend the derailelellueur enough for shifting to fail?

          • Fallibilist@feddit.uk
            link
            fedilink
            English
            arrow-up
            4
            arrow-down
            4
            ·
            2 months ago

            Why is it every time someone starts a sentence with “So you’re saying…” it’s then followed with misrepresentation of what was actually said?

            No, that is not what I said. What I did say is that in the vast number of cases when your shifting is shit it’s not because of bent derailleur or badly adjusted one but it’s a bent derailleur hanger. That part is designed to bend specifically so that the derailleur itself doesn’t.